Lenze 9400 Manual de usuario descargar pdf (Pagina 621)

Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06 621

13 Diagnostics & fault analysis

13.7 Error messages of the operating system

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

0x00680015 6815765 MXI1: Module has been changed Information or warning locked if

the hardware type has also

changed.

-

0x0068000a

6815754 MXI1: Module is defective or missing Fault -

0x008c000d

9175053 MXI1: Module is missing or incompatible Fault -

0x008c000f

9175055 MXI1: PROFIBUS module is missing or incompatible Fault C00615/2

0x00680010 6815760 MXI1: Wrong module System fault -

0x008c0018

9175064 MXI2: CAN module is missing or incompatible Fault C00615/3

0x008c0014 9175060 MXI2: Digital frequency module is missing or incompatible Fault C00615/3

0x008c0012 9175058 MXI2: Ethernet module is missing or incompatible Fault C00615/3

0x008c0016 9175062 MXI2: ICM module is missing or incompatible Fault C00615/3

0x00680005 6815749 MXI2: Module changed during operation Warning locked -

0x00680016

6815766 MXI2: Module has been changed Information or warning locked if

the hardware type has also

changed.

-

0x0068000b

6815755 MXI2: Module is defective or missing System fault -

0x008c000e

9175054 MXI2: Module is missing or incompatible Fault -

0x008c0010

9175056 MXI2: PROFIBUS module is missing or incompatible Fault C00615/3

0x00680011 6815761 MXI2: Wrong module System fault -

0x00b8000a

12058634 Negative direction of rotation limited Information C02716/1

0x00b80002 12058626 Negative limit switch has triggered Quick stop by trouble -

0x00b80008

12058632 Negative software limit switch overtravelled Quick stop by trouble C02716/2

0x006a0003 6946819 New applications loaded Information -

0x00910002

9502722 No heartbeat signal detected System fault -

0x0090000a

9437194 No parameters for module in MXI1 Fault C00615/2

0x0090000b 9437195 No parameters for module in MXI2 Fault C00615/3

0x007b0010 8060944 Overcurrent detected Fault -

0x00900000

9437184 Parameter set faulty Fault -

0x00900003

9437187 Parameter set loaded Information -

0x00900005

9437189 Parameter set restored Fault -

0x00900002

9437186 Parameter set saved Information -

0x00900009

9437193 Parameter set: type of standard device has been changed Information -

0x00900007

9437191 Parameter set: Version conflict Fault -

0x006a0015

6946837 PDO mapping (MXI1): Faulty configuration Fault -

0x006a0016

6946838 PDO mapping (MXI2): Faulty configuration Fault -

0x00b80000

12058624 PLC configuration invalid Fault -

0x007d0001

8192001 PLC configuration invalid Fault -

0x007b0037

8060983 PLC configuration invalid Fault -

0x00750006

7667718 PLC configuration invalid Fault -

0x006a0012

6946834 Pointer access in impermissible memory area Fault -

0x007b004a

8061002 Pole position identification cancelled Fault C00640

0x00b8000f 12058639 Position target outside the software limit positions Quick stop by trouble C02716/2

0x00910010 9502736 Position value faulty Fault -

0x00b80009

12058633 Positive direction of rotation limited Information C02716/1

0x00b80001 12058625 Positive limit switch has triggered Quick stop by trouble -

0x00b80007

12058631 Positive software limit switch overtravelled Quick stop by trouble C02716/2

0x00680014 6815764 Power section has been changed Information or warning locked if

the hardware type has also

changed.

-

0x0068000f

6815759 Power section incompatible System fault -

0x00680001

6815745 Power section is defective System fault -

0x00680009

6815753 Power section is defective System fault -

0x007b0042

8060994 Power section is defective System fault -

0x008c000a

9175050 Project not available Fault -

hex dec Error message Response (Lenze setting) can be set in

1 2 ... 616 617 618 619 620 621 622 623 624 625 626 ... 953 954

Comentarios a estos manuales

Sin comentarios