Lenze 9400 Manual de usuario descargar pdf (Pagina 617)

Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06 617

13 Diagnostics & fault analysis

13.7 Error messages of the operating system

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

0x00690000 6881280 Code refresh System fault -

0x00680019

6815769 Combination MXI1/MXI2 not possible System fault -

0x0068001f

6815775 Combination of memory module/device not possible System fault -

0x00680020

6815776 Combination of module in MXI1/device not possible System fault -

0x00680021

6815777 Combination of module in MXI2/device not possible System fault -

0x007f0002

8323074 Communication error between device and device module No response C01501

0x0091000e 9502734 Communication task: Standstill > 3 s Fault C01230

0x007f0003 8323075 Communication with module in MXI1 interrupted Information -

0x007f0004

8323076 Communication with module in MXI2 interrupted Information -

0x00920001

9568257 Communication with safety module interrupted Information -

0x008c001a

9175066 ConnectTable active Information -

0x0068000e

6815758 Control card incompatible System fault -

0x00680000

6815744 Control card is defective System fault -

0x00680008

6815752 Control card is defective System fault -

0x00780008

7864328 Control card is defective (UB18 neg.) System fault -

0x00780004

7864324 Control card is defective (UB24) System fault -

0x00780006

7864326 Control card is defective (UB8) System fault -

0x00780007

7864327 Control card is defective (VCC15 neg.) System fault -

0x00780005

7864325 Control card is defective (VCC15) System fault -

0x00780009

7864329 Control card is defective (VCC5) System fault -

0x006f0000

7274496 Control card: Supply voltage (24 V DC) too low Trouble -

0x00750001

7667713 Controller enabled Information -

0x00750003

7667715 Controller in STO state Information -

0x007b0047

8060999 Controller: Clamp operation Information -

0x007b0035

8060981 Controller: Overload during acceleration phases Fault -

0x00750005

7667717 Controller: Pulse inhibit is active Information -

0x00770009

7798793 CPU: Overtemperature Warning -

0x00770008

7798792 CPU: Temperature > C00126 No response C00589

0x0077000e 7798798 CPU: thermal detector is defective Fault C00588

0x0091000f 9502735 Cyclic task: Standstill > 60 s Information -

0x0077000d

7798797 DC-bus capacitor: thermal detector is defective Fault C00588

0x007b000e 8060942 DC-bus overvoltage Trouble C00600

0x007b000f 8060943 DC-bus undervoltage Trouble -

0x00b8000d

12058637 Deceleration has been limited Information C02716/3

0x00780001 7864321 Device utilisation Ixt > 100 % Fault -

0x00780000

7864320 Device utilisation Ixt > C00123 Warning C00604

0x00990003 10027011 DFIN (MXI1): Signal error enable/lamp control Warning C13041

0x00990004 10027012 DFIN (MXI1): Supply cannot be corrected anymore Warning C13042

0x00990000 10027008 DFIN (MXI1): Track error A-/A Fault C13040

0x00990001 10027009 DFIN (MXI1): Track error B-/B Fault C13040

0x00990002 10027010 DFIN (MXI1): Track error Z-/Z Fault C13040

0x00aa0003 11141123 DFIN (MXI2): Signal error enable/lamp control Warning C14041

0x00aa0004 11141124 DFIN (MXI2): Supply cannot be corrected anymore Warning C14042

0x00aa0000 11141120 DFIN (MXI2): Track error A-/A Fault C14040

0x00aa0001 11141121 DFIN (MXI2): Track error B-/B Fault C14040

0x00aa0002 11141122 DFIN (MXI2): Track error Z-/Z Fault C14040

0x00990005 10027013 DFOUT (MXI1): Maximum frequency reached Warning C13080

0x00aa0005 11141125 DFOUT (MXI2): Maximum frequency reached Warning C14080

0x0090000c 9437196 Disconnection in the case of par. storage Fault -

0x006a0011

6946833 Division by zero Fault -

0x007b0011

8060945 Earth fault detected Fault -

0x0068001d

6815773 Electronic nameplate: Checksum error Warning -

hex dec Error message Response (Lenze setting) can be set in

1 2 ... 612 613 614 615 616 617 618 619 620 621 622 ... 953 954

Comentarios a estos manuales

Sin comentarios