Lenze ETC Motion Control Manual de usuario Pagina 190
- Pagina / 428
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Machine constants
Basics
4
4.1
l
190
EDSTCXN EN 2.0
4 Machine constants
This chapter describes the machine constants (MCs) of the controls ETCPC
and ETCHC. Some of the described MCs are not available in both control
types due to the different hardware features. The respective identifiers are
marked with a corresponding footnote.
4.1 Basics
MCs are used to adapt the control to the specific field of application. These
include the actual machine with its axes as well as the fields of technology
and operating philosophy. Therefore, the extent to which the end customers
and users can affect the MCs should be limited.
At the end of this chapter, you can find a complete overview of the MCs
including comments. This overview is included in the supply of each
ETC−MMI under the name MUSTER.MK (SAMPLE.MC), but can also be
supplied separately.
) Note!
The file "MUSTER.MK" ("SAMPLE.MC") serves as a basis for your
specific adaptations. Therefore, it is recommended to generate a
copy of the file. The name of the file is irrelevant. It must be
provided with the extension ".MK". However, it is recommended
to use a name that is related to the machine, e.g. the machine
number.
The file can be transferred to the control in two different ways. Either via an
ETC−MMI whenever the control is restarted or by means of any terminal
program via the monitor interface of the control. In the first case, the file is
stored on the hard disk of the PC. The second case is only necessary if no
PC−supported MMI is connected to the control.
The MCs are stored in the control in a non−volatile memory. This is where
they are updated if the MCs are changed in any way. Controls delivered ex
works do not contain an MC file. Therefore, the message "keine
Maschinenkonstantendatei geladen" ("no machine constants file loaded")
appears when the control is first put into operation.
When adapting the MC file, please make sure that MCs which are not
included in the MC file are not reset to the default value, but keep the
previously set value. However, to gain a better overview, all MCs should be
described in the MC file. Some MCs have a limited value range. If the entered
value lies outside this value range, it will be limited to this range.
- ETC Motion Control 1
- Contents i 3
- Contentsi 4
- Target group 10
- Contents 10
- Further information 10
- EDSTCXN EN 2.0 11
- EDSTCXN EN 2.0 12
- ETCHN003 13
- ETCHT000 13
- Getting started 14
- EETCN095 33
- ETCN010 ETCN009 45
- ETCNC097 71
- 3 CNC programming 87
- CNC programming 100
- 3.2.2.36 G99 Return 125
- 50 mm here 126
- G120 AXES 134
- In S0: offset = S0+Tm 158
- S0 without shift 164
- XOR(x,y) 173
- (−> P586) from 181
- Machine constants 190
- 4 Machine constants 190
- 0, /* axis interfaces */ 233
- Definitions 246
- Data block 1 246
- Verfahrtaste 258
- 110 0 100 110 0 258
- SPS-Achse am Ziel 258
- Data blocks 8 ... 14 271
- ETC−MMI−Gateway 276
- 6 ET −MMI gateway 276
- ETCN001 ETCN002 277
- 7 ETC−MMI 286
- Installing ETC−MMI 287
- W Programs W Lenze W ETC 288
- Showing a new softkey line 291
- (submenu) 291
- ETCN076 306
- Set filter 307
- ETCN077 308
- File manager 309
- Appendix 328
- SPS_EXEC 334
- PLC programming 336
- 8 PLC programming 336
- %MW1.42 ARRAY[0..1] OF BYTE 357
- %MW1.43 ARRAY[0..1] OF BYTE 357
- 10987654321 428
Comentarios a estos manuales
Relacionado con productos y manuales para Software Lenze ETC Motion Control
Software Lenze PLC Designer V2.x Manual de usuario
(336 paginas)
(336 paginas)
(30 paginas)
Software Lenze Cam Designer Basic Manual de usuario
(53 paginas)
(53 paginas)
Software Lenze Card File Handler Manual de usuario
(37 paginas)
(37 paginas)
Samsung SE-S164L-AMBN Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Lager Samsung SE-S164L-AMBN.
Wir stellen 1 PDF-Handbücher Samsung SE-S164L-AMBN zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
rasha