Lenze ETC Motion Control Manual de usuario Pagina 115
- Pagina / 428
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CNC programming
G functions
G functions individual descriptions
3
3.2
3.2.2
l
115
EDSTCXN EN 2.0
3.2.2.20 G37 Modal oscillation "off"
G37 AXES
AXES Validity identification for the axes, for which the modal oscillation should
be switched off. Value = 1.
With the preparatory function G37, the modal oscillation (see G36) is
switched off. To achieve this, a 1 is programmed in a block with the
preparatory function G37 under the address of the axis, whose modal
oscillation should be switched off.
The axis is then stopped immediately, i.e. it does not travel its oscillation
stroke to the end.
N15 G37 Z1 In block 15, the modal oscillation of the Z axis is stopped.
3.2.2.21 G40 Deactivate tool correction
Switch off the tool path correction which was switched on by G41 / G42.
G40 E
E Selection of the departure strategy, only with standard TRC.
0: a departure block must follow G40 (default).
1: no departure block after G40, the axes remain on the last corrected
position.
G40 switches off the correction procedure which was switched on with G41
or G42 again. A tool radius compensation is provided by default.
The uncorrected target point is approached with the next traversing block.
It must be noted that a traversing block must always be programmed for the
TRC following G40, if E1 is not specified. The starting point of this block is on
the compensated path, the target point of the block is uncompensated!
N 100 G1 X10 Y10 Last profile block within the TRC
N 110 G40 TRC "off"
N 120 G1 X0 Departure block
Syntax
Meaning of the addresses
Explanation
Example
Syntax
Meaning of the addresses
Explanation
Example
- ETC Motion Control 1
- Contents i 3
- Contentsi 4
- Target group 10
- Contents 10
- Further information 10
- EDSTCXN EN 2.0 11
- EDSTCXN EN 2.0 12
- ETCHN003 13
- ETCHT000 13
- Getting started 14
- EETCN095 33
- ETCN010 ETCN009 45
- ETCNC097 71
- 3 CNC programming 87
- CNC programming 100
- 3.2.2.36 G99 Return 125
- 50 mm here 126
- G120 AXES 134
- In S0: offset = S0+Tm 158
- S0 without shift 164
- XOR(x,y) 173
- (−> P586) from 181
- Machine constants 190
- 4 Machine constants 190
- 0, /* axis interfaces */ 233
- Definitions 246
- Data block 1 246
- Verfahrtaste 258
- 110 0 100 110 0 258
- SPS-Achse am Ziel 258
- Data blocks 8 ... 14 271
- ETC−MMI−Gateway 276
- 6 ET −MMI gateway 276
- ETCN001 ETCN002 277
- 7 ETC−MMI 286
- Installing ETC−MMI 287
- W Programs W Lenze W ETC 288
- Showing a new softkey line 291
- (submenu) 291
- ETCN076 306
- Set filter 307
- ETCN077 308
- File manager 309
- Appendix 328
- SPS_EXEC 334
- PLC programming 336
- 8 PLC programming 336
- %MW1.42 ARRAY[0..1] OF BYTE 357
- %MW1.43 ARRAY[0..1] OF BYTE 357
- 10987654321 428
Comentarios a estos manuales
Relacionado con productos y manuales para Software Lenze ETC Motion Control
Software Lenze PLC Designer V2.x Manual de usuario
(336 paginas)
(336 paginas)
(30 paginas)
Software Lenze Cam Designer Basic Manual de usuario
(53 paginas)
(53 paginas)
Software Lenze Card File Handler Manual de usuario
(37 paginas)
(37 paginas)
Terrawave V12106-C60-V-6 manuales
Manuales del propietario y guías del usuario para Hardware Terrawave V12106-C60-V-6.
Ofrecemos 1 manuales en pdf Terrawave V12106-C60-V-6 para descargar gratis por tipos de documentos: Manual de usuario
rasha