Lenze 8200 Frequency inverters Manual de usuario Pagina 135
- Pagina / 311
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
During operation
8200SHB01996-2
6.1.2 822X/824X
- The controllers 822X/824X have a temperature-dependent fan circuit:
- The fans are only activated when the heat sink temperature, which is a
fixed factory setting, is exceeded.
6.1.3 8218-V003
- For use of the variant 8218-V003 with the Lenze convection cooling system:
- Depending on the application conditions, the temperature monitoring
(message ”OH”) can be activated during low-noise operation with a
16 kHz chopper frequency (C018=-5-).
6.2 Display of the controller status
During operation without an operating module, the operating state of the controller
is displayed on two LEDs at the front of the unit.
LED Operating status
green red
on off Controller enabled
on on Mains switched on and automatic start inhibited (AS_LC)
blinking off Controller inhibited
off blinkingeverysecond Fault message
off blinking every 0.4 seconds Undervoltage switch-off
off off Programming mode (only820X)
Show/Hide Bookmarks
- = Global Drive 1
- Contents of the Manual 3
- 8200SHB0199ii 6
- 8200SHB0199iv 8
- Contents 10
- 8200SHB0199vi 10
- 8200SHB0199x 14
- 1.1 How to use this Manual 17
- 1.2 Scope of delivery 17
- 8200SHB01991-2 18
- 1.3 Legal regulations 19
- 8200SHB01991-4 20
- 8200SHB01991-6 22
- 8200SHB01991-8 24
- Directive 25
- 8200SHB01991-10 26
- 1.4.5 EC Machinery Directive 27
- 8200SHB01991-12 28
- EC Manufacturer’s Declaration 28
- Safety information 29
- Technical Data 33
- 8200SHB01993-4 36
- 8200SHB01993-24 56
- 3.7.1 Features 56
- 4 Installation 58
- 4.1.1 Important notes 58
- 8200SHB01994-2 59
- 8200SHB01994-6 63
- 4.1.2.5 Types 8221 to 8227 63
- 4.1.2.6 Types 8241 to 8246 64
- 8200SHB01994-10 67
- (”push-through technique”) 67
- 4.1.4.1 Types 8215 to 8218 68
- 8200SHB01994-12 69
- 4.1.4.2 Types 8221 to 8227 69
- 4.1.4.3 Types 8241 to 8246 70
- 8200SHB01994-14 71
- 4.1.5.1 General 71
- 4.1.5.2 Demands on the cooler 72
- 8200SHB01994-16 73
- 4.1.5.4 Assembly preparations 74
- 8200SHB01994-18 75
- 8200SHB01994-20 77
- 8200SHB01994-22 79
- 8200SHB01994-24 81
- 4.2 Electrical installation 82
- 4.2.1 Operator’s safety 82
- 8200SHB01994-26 83
- 4.2.3 Motor protection 83
- 8200SHB01994-30 87
- 8200SHB01994-32 89
- 8200SHB01994-34 91
- 4.2.7.4 Connection plan 820X 92
- 8200SHB01994-36 93
- 4.2.7.5 Connection plan 821X 93
- 8200SHB01994-40 97
- 4.2.8.3 Connection diagrams 98
- 8200SHB01994-42 99
- Installation 100
- 8200SHB0199 100
- 8200SHB01994-44 101
- 8200SHB01994-46 103
- Edition of: 01/1999 105
- 5 Commissioning 106
- Commissioning 106
- 8200SHB01995-16 121
- 8200SHB01995-18 123
- 8200SHB01995-20 125
- 8200SHB01995-22 127
- 8200SHB01995-24 129
- 8200SHB01995-26 131
- 5.5.4 Air conditioning system 131
- 8200SHB01995-28 133
- During operation 134
- 6 During operation 134
- 6.1 Operating information 134
- 6.1.1 General 134
- 8200SHB01996-2 135
- 6.1.2 822X/824X 135
- 6.1.3 8218-V003 135
- Configuration 138
- 7 Configuration 138
- 8200SHB01997-2 139
- 7.1 8201BB operating module 139
- 8200SHB01997-4 141
- 7.2.1 Operating level 141
- 7.2.2 Code level 141
- 7.2.3 Parameter level 142
- 8200SHB01997-6 143
- 8200SHB01997-8 145
- 7.4 Operating functions 146
- 7.4.1 Operating mode 146
- 8200SHB01997-10 147
- 8200SHB01997-12 149
- 8200SHB01997-14 151
- 8200SHB01997-20 157
- 8200SHB01997-22 159
- 7.5.6 V/f characteristic 159
- 7.5.6.1 V/f-rated frequency f 159
- 8200SHB01997-26 163
- 7.5.7 Configuration 163
- 7.5.8 Motor data detection 164
- 7.5.9.2 Chopper frequency 166
- 8200SHB01997-30 167
- 7.5.9.3 Oscillation damping 168
- 8200SHB01997-32 169
- 7.5.9.5 Skip frequencies 170
- 8200SHB01997-34 171
- 8200SHB01997-36 173
- 7.5.10.3 Frequency precontrol 176
- 8200SHB01997-40 177
- 7.5.11 Setpoint input 177
- 8200SHB01997-42 179
- 7.5.11.6 Setpoint sum 184
- 8200SHB01997-48 185
- 7.5.12 Controller enable RFR 185
- 8200SHB01997-50 187
- 8200SHB01997-52 189
- 8200SHB01997-56 193
- 8200SHB01997-58 195
- 7.5.14.7 TRIP set 195
- 8200SHB01997-60 197
- 8200SHB01997-64 201
- 8200SHB01997-72 209
- 7.7.3.2 PTC input 209
- 8200SHB01997-74 211
- 8200SHB01997-80 217
- 8200SHB01997-82 219
- 8200SHB01997-86 223
- 8200SHB01997-90 227
- 8200SHB01997-94 231
- 8200SHB01997-96 233
- 8.1 Troubleshooting 236
- 8.3 Fault messages 237
- 8200SHB01998-4 239
- 8.4 Reset of fault messages 239
- Maintenance 240
- 9 Maintenance 240
- 9.1 Maintenance services 240
- 8200SHB01999-2 241
- 9.2 Service addresses 241
- Network of several drives 244
- 10 Network of several drives 244
- 10.1 Function 244
- 10.3.1 Conditions 252
- 10.3 Selection basics 252
- 8200SHB019910-18 261
- Instructions 262
- Application of brake units 264
- 11 Application of brake units 264
- 8200SHB019911-2 265
- Automation 267
- 12 Automation 267
- Accessories 270
- 13 Accessories (Survey) 270
- 13.2 Software 270
- 8200SHB019913-2 271
- 13.3.1 Types 820X 271
- 13.3.2 Types 821X 272
- 8200SHB019913-4 273
- 13.3.3 Types 822X 273
- 13.3.4 Types 824X 274
- 8200SHB019913-6 275
- Selection help 278
- 14 Selection help 278
- 8200SHB019914-2 279
- Application examples 280
- 15 Application examples 280
- 8200SHB019915-2 281
- Show/Hide Bookmarks 285
- 8200SHB019915-8 287
- 15.4 Air conditioning system 287
- 8200SHB019915-10 289
- Signal flow charts 292
- 16 Signal-flow charts 292
- 16.1.1 Control structure 293
- 16.1.2 Inverter control 294
- 16.1.3 Monitorings 294
- Glossary 302
- 17 Glossary 302
- 8200SHB019917-2 303
- Table of keyw ords 304
Relacionado con productos y manuales para Hardware Lenze 8200 Frequency inverters
Hardware Lenze E82ZMBRB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze ECSCMxxx Manual de usuario
(375 paginas)
(375 paginas)
Hardware Lenze ECSZZxxxxxx Manual de usuario
(68 paginas)
(68 paginas)
Hardware Lenze EDK82MVXXX Manual de usuario
(16 paginas)
(16 paginas)
Hardware Lenze EZN3x0015H230 Manual de usuario
(64 paginas)
(64 paginas)
Hardware Lenze EDB9300UES Manual de usuario
(175 paginas)
(175 paginas)
Hardware Lenze EPM−H606 Manual de usuario
(170 paginas)
(170 paginas)
(124 paginas)
Hardware Lenze E82ZM11334B Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze ECSCPxxx Manual de usuario
(455 paginas)
(455 paginas)
Hardware Lenze LDECBBF1xxxxxxHx Manual de usuario
(110 paginas)
(110 paginas)
Hardware Lenze EMF2175IB Manual de usuario
(152 paginas)
(152 paginas)
Hardware Lenze GDC with OPC Manual de usuario
(8 paginas)
(8 paginas)
Hardware Lenze E82MVxxx 2Bxxx Manual de usuario
(206 paginas)
(206 paginas)
Hardware Lenze EZZ0013 Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.220 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales