Lenze EPM−T9XX Modular system Manual de usuario Pagina 336
- Pagina / 544
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Parameterising 2/4xcounter module
2 × 32 bit counter with GATE and RES level−triggered (modes 12 and 13)
12
Parameter setting via system bus (CAN) / CANopen
12.4
12.4.7
L
12.4−16
EDSPM−TXXX−9.0−11/2009
12.4.7 2 × 32 bit counter with GATE and RES level−triggered (modes 12 and 13)
epm−t082
Fig. 12.4−23 Terminal assignment of the 2/4xcounter in the modes 12 and 13
In the modes 12 and 13, two 32−bit counters are available, which are controlled via
a gate signal (gate). A starting value and a comparison value can be assigned to
each counter.
The modules differ in having different counting directions:
Mode 12: Upcounter.
Mode 13: Downcounter
If a HIGH level is applied to input IN3 / IN6 (GATE), the counter is incremented or
decremented by 1 with each LOW/HIGH edge.
During the counting process, a LOW level must be applied to input IN1 / IN4 (RES).
A HIGH level deletes the counter.
Once the counter reaches the value loaded in the "Compare" register, output
OUT0 / OUT1 is set to HIGH level for at least 100 ms, with the counter continuing
its task.
Terminal assignment
GATE/CLK signal
RES signal
OUT signal
- I/O−System IP20 1
- Contents 10
- 1 Preface 11
- 1.1 The I/O system IP20 13
- How to use this System Manual 16
- Document history 17
- 1.2.3 Document history 17
- 1.3 Legal regulations 19
- Legal regulations 20
- Safety instructions 21
- Technical data 25
- The modular system 100
- The compact system 113
- EPM-T831 1A.10 127
- EPM-T833 1A.10 135
- 02413567 143
- Mechanical installation 147
- Electrical installation 155
- 8.1 Via system bus (CAN) 171
- 8.2 Network management (NMT) 173
- Network management (NMT) 174
- 8.3 Transmitting process data 175
- Transmitting process data 176
- PDO1-TX PDO1-RX 178
- 2. 3. 4 178
- Transmitting parameter data 188
- Telegram structure 188
- Identifier = 1538 190
- Identifier = 1410 190
- 8.6 Node Guarding 195
- Node Guarding 196
- 8.7 Heartbeat 197
- Heartbeat 198
- 8.8 Reset node 199
- 8.9 Monitoring 201
- Monitoring 202
- Digital output monitoring 202
- 8.10 Diagnostics 205
- Diagnostics 206
- Emergency telegram 206
- 8.10.1 Emergency telegram 206
- Status of the digital outputs 208
- Via the index I6401 209
- Via the index I6411 209
- Network via CANopen 211
- Networking via PROFIBUS−DP 255
- Commissioning 283
- 12.1 Important notes 295
- Parameterising analog modules 300
- Parameter data 300
- Diagnostic data 304
- 12.3.2 Diagnostic data 304
- 12.3−11 309
- 12.3−12 310
- 12.3−13 311
- 12.3−16 314
- 12.3−17 315
- 12.3−18 316
- Input data / output data 325
- 2 x 32 bit counter (mode 0) 326
- Encoder (modes 1, 3, and 5) 328
- Counter 0 332
- Counter 1 332
- 12.4−13 333
- 12.4−14 334
- 12.4−15 335
- 12.4−16 336
- 12.4−17 337
- 12.4−18 338
- 12.4−19 339
- 12.4−20 340
- 12.4−21 341
- 12.4−22 342
- 12.4−23 343
- 12.4−24 344
- 12.4−25 345
- 12.4−26 346
- 12.4−27 347
- 12.4−28 348
- 12.4−30 350
- 12.4−31 351
- 12.4−32 352
- 12.4−33 353
- 12.4−34 354
- 12.4−35 355
- 12.4−36 356
- 12.4−37 357
- 12.4−38 358
- 12.4−39 359
- 12.4−40 360
- 12.4−41 361
- 12.4−42 362
- 12.4−43 363
- 12.4−44 364
- 12.4−45 365
- 12.4−46 366
- 12.4−47 367
- 12.4−48 368
- 12.4−49 369
- 12.4−50 370
- 12.4−51 371
- 12.4−52 372
- 12.4−53 373
- 12.4−54 374
- 12.4−55 375
- 12.4−56 376
- Parameterising SSI interface 379
- EDSPM−TXXX−9.0−11/2009 384
- 12.5−11 387
- Encoder (mode 0) 395
- 12.6.3 Encoder (mode 0) 395
- 32 bit counter (mode 1) 397
- 12.6−10 400
- 12.6−11 401
- 12.6−12 402
- 12.6−13 403
- Measuring the period (mode 4) 404
- 12.6−15 405
- 12.8 Loading default setting 409
- · Example: 413
- 13.1−11 423
- 13.1−12 424
- 13.1−14 426
- 13.1−16 428
- 13.1−17 429
- 13.1−18 430
- Gateway Counter 438
- Data to module 438
- Data from module 438
- In3/In6 (DIR) 446
- 13.2−13 447
- 13.2−14 448
- 13.2−15 449
- Counter access 450
- 13.2−17 451
- 13.2−18 452
- 13.2−19 453
- 13.2−20 454
- 13.2−21 455
- 13.2−22 456
- 13.2−23 457
- 13.2−24 458
- 13.2−25 459
- 13.2−26 460
- 13.2−27 461
- 13.2−29 463
- 13.2−30 464
- 13.2−31 465
- 13.2−32 466
- 13.2−33 467
- 13.2−34 468
- 13.2−36 470
- 13.2−37 471
- 13.2−38 472
- 13.2−40 474
- In3/In6 (B) 475
- 13.2−42 476
- 13.2−43 477
- 13.2−44 478
- 13.2−46 480
- 13.2−47 481
- 13.2−48 482
- 13.2−49 483
- 13.2−50 484
- 13.2−52 486
- 13.2−54 488
- 13.2−55 489
- 13.3.1 Parameter data 491
- Gateway SSI-Interface 493
- 13.4.1 Parameter data 495
- Gateway Counter/Dig In 496
- 13.4.3 Encoder (mode 0) 498
- Signal characteristic 503
- 13.4−10 504
- 13.4−11 505
- 13.4−12 506
- 13.4−14 508
- 14.1 Fault messages 511
- Appendix 513
- 10987654321 544
Relacionado con productos y manuales para Hardware Lenze EPM−T9XX Modular system
Hardware Lenze E82MV752 4Bxxx Manual de usuario
(20 paginas)
(20 paginas)
Hardware Lenze EMZ9374IB Manual de usuario
(122 paginas)
(122 paginas)
Hardware Lenze EZN3x0060H054 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze EPM-H521 Manual de usuario
(136 paginas)
(136 paginas)
Hardware Lenze MC−xxx Card Manual de usuario
(46 paginas)
(46 paginas)
Hardware Lenze EWS1001 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Lenze EWS1003 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Lenze E93ZWLX Manual de usuario
(77 paginas)
(77 paginas)
Hardware Lenze EMZ2221IB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze E82ZMBRB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze ECSCMxxx Manual de usuario
(375 paginas)
(375 paginas)
Hardware Lenze ECSZZxxxxxx Manual de usuario
(68 paginas)
(68 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales