Lenze EPM−T9XX Modular system Manual de usuario Pagina 287
- Pagina / 544
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System bus (CAN) / CANopen
Commissioning examples
11
Commissioning
11.1
11.1.2
L
11.1−3
EDSPM−TXXX−9.0−11/2009
Please also note relevant information on the controller in the System Manual!
Setting sequence:
1. Set CAN bus node address to value 1 (C0350 = 1).
2. Address for CAN3−IN and CAN3−OUT to be defined by C0350 (C0353/3 = 0).
3. Set CAN bus baud rate to 500 kbits/s (C0351 = 0).
4. Set CAN bus master operation (C0352 = 1).
5. Set cycle time for cyclical process data transfers (C0356/3 > 0).
6. Switch process output words in CAN3−OUT to digital output signals
(C0864/3 = 1).
7. Save set parameters (C0003 = 1).
8. Trigger CAN Reset Node (C0358 = 1).
) Note!
When using an 8200 vector frequency inverter, make sure to set
the process data channel CAN−I/O from sync−controlled to
event−controlled transmission (C0360 = 0) .
The modified settings will be accepted after a "Reset Node"
(C0358 = 1).
Settings at the controller
- I/O−System IP20 1
- Contents 10
- 1 Preface 11
- 1.1 The I/O system IP20 13
- How to use this System Manual 16
- Document history 17
- 1.2.3 Document history 17
- 1.3 Legal regulations 19
- Legal regulations 20
- Safety instructions 21
- Technical data 25
- The modular system 100
- The compact system 113
- EPM-T831 1A.10 127
- EPM-T833 1A.10 135
- 02413567 143
- Mechanical installation 147
- Electrical installation 155
- 8.1 Via system bus (CAN) 171
- 8.2 Network management (NMT) 173
- Network management (NMT) 174
- 8.3 Transmitting process data 175
- Transmitting process data 176
- PDO1-TX PDO1-RX 178
- 2. 3. 4 178
- Transmitting parameter data 188
- Telegram structure 188
- Identifier = 1538 190
- Identifier = 1410 190
- 8.6 Node Guarding 195
- Node Guarding 196
- 8.7 Heartbeat 197
- Heartbeat 198
- 8.8 Reset node 199
- 8.9 Monitoring 201
- Monitoring 202
- Digital output monitoring 202
- 8.10 Diagnostics 205
- Diagnostics 206
- Emergency telegram 206
- 8.10.1 Emergency telegram 206
- Status of the digital outputs 208
- Via the index I6401 209
- Via the index I6411 209
- Network via CANopen 211
- Networking via PROFIBUS−DP 255
- Commissioning 283
- 12.1 Important notes 295
- Parameterising analog modules 300
- Parameter data 300
- Diagnostic data 304
- 12.3.2 Diagnostic data 304
- 12.3−11 309
- 12.3−12 310
- 12.3−13 311
- 12.3−16 314
- 12.3−17 315
- 12.3−18 316
- Input data / output data 325
- 2 x 32 bit counter (mode 0) 326
- Encoder (modes 1, 3, and 5) 328
- Counter 0 332
- Counter 1 332
- 12.4−13 333
- 12.4−14 334
- 12.4−15 335
- 12.4−16 336
- 12.4−17 337
- 12.4−18 338
- 12.4−19 339
- 12.4−20 340
- 12.4−21 341
- 12.4−22 342
- 12.4−23 343
- 12.4−24 344
- 12.4−25 345
- 12.4−26 346
- 12.4−27 347
- 12.4−28 348
- 12.4−30 350
- 12.4−31 351
- 12.4−32 352
- 12.4−33 353
- 12.4−34 354
- 12.4−35 355
- 12.4−36 356
- 12.4−37 357
- 12.4−38 358
- 12.4−39 359
- 12.4−40 360
- 12.4−41 361
- 12.4−42 362
- 12.4−43 363
- 12.4−44 364
- 12.4−45 365
- 12.4−46 366
- 12.4−47 367
- 12.4−48 368
- 12.4−49 369
- 12.4−50 370
- 12.4−51 371
- 12.4−52 372
- 12.4−53 373
- 12.4−54 374
- 12.4−55 375
- 12.4−56 376
- Parameterising SSI interface 379
- EDSPM−TXXX−9.0−11/2009 384
- 12.5−11 387
- Encoder (mode 0) 395
- 12.6.3 Encoder (mode 0) 395
- 32 bit counter (mode 1) 397
- 12.6−10 400
- 12.6−11 401
- 12.6−12 402
- 12.6−13 403
- Measuring the period (mode 4) 404
- 12.6−15 405
- 12.8 Loading default setting 409
- · Example: 413
- 13.1−11 423
- 13.1−12 424
- 13.1−14 426
- 13.1−16 428
- 13.1−17 429
- 13.1−18 430
- Gateway Counter 438
- Data to module 438
- Data from module 438
- In3/In6 (DIR) 446
- 13.2−13 447
- 13.2−14 448
- 13.2−15 449
- Counter access 450
- 13.2−17 451
- 13.2−18 452
- 13.2−19 453
- 13.2−20 454
- 13.2−21 455
- 13.2−22 456
- 13.2−23 457
- 13.2−24 458
- 13.2−25 459
- 13.2−26 460
- 13.2−27 461
- 13.2−29 463
- 13.2−30 464
- 13.2−31 465
- 13.2−32 466
- 13.2−33 467
- 13.2−34 468
- 13.2−36 470
- 13.2−37 471
- 13.2−38 472
- 13.2−40 474
- In3/In6 (B) 475
- 13.2−42 476
- 13.2−43 477
- 13.2−44 478
- 13.2−46 480
- 13.2−47 481
- 13.2−48 482
- 13.2−49 483
- 13.2−50 484
- 13.2−52 486
- 13.2−54 488
- 13.2−55 489
- 13.3.1 Parameter data 491
- Gateway SSI-Interface 493
- 13.4.1 Parameter data 495
- Gateway Counter/Dig In 496
- 13.4.3 Encoder (mode 0) 498
- Signal characteristic 503
- 13.4−10 504
- 13.4−11 505
- 13.4−12 506
- 13.4−14 508
- 14.1 Fault messages 511
- Appendix 513
- 10987654321 544
Relacionado con productos y manuales para Hardware Lenze EPM−T9XX Modular system
Hardware Lenze E82MV752 4Bxxx Manual de usuario
(20 paginas)
(20 paginas)
Hardware Lenze EMZ9374IB Manual de usuario
(122 paginas)
(122 paginas)
Hardware Lenze EZN3x0060H054 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze EPM-H521 Manual de usuario
(136 paginas)
(136 paginas)
Hardware Lenze MC−xxx Card Manual de usuario
(46 paginas)
(46 paginas)
Hardware Lenze EWS1001 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Lenze EWS1003 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Lenze E93ZWLX Manual de usuario
(77 paginas)
(77 paginas)
Hardware Lenze EMZ2221IB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze E82ZMBRB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze ECSCMxxx Manual de usuario
(375 paginas)
(375 paginas)
Hardware Lenze ECSZZxxxxxx Manual de usuario
(68 paginas)
(68 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.247 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales