Lenze EPM−T9XX Modular system Manual de usuario Pagina 289
- Pagina / 544
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System bus (CAN) / CANopen
Commissioning examples
11
Commissioning
11.1
11.1.2
L
11.1−5
EDSPM−TXXX−9.0−11/2009
When using the communication profile CANopen
1. Adapt the basic identifiers for the process data object 1.
– Set PDO1−Rx via index 1400
h
, and subindex 1 to 770.
– Set PDO1−Tx via index 1800
h
, and subindex 1 to 769.
2. Make a "reset node" by setting the index I2358
h
= 1. The settings are
accepted.
Setting of the baud rate and node address:
CANopen Baud rate
Coding switch value [kbit/s]
80 1000
81 500
82 250
83 125
84 100
85 50
86 20
87 10
88 800
Bold print = Lenze setting
1. Switch the CAN gateway module voltage supply off.
2. Use the coding switch to set the required baud rate.
– Select value 91.
3. Switch the CAN gateway module voltage supply on.
– The LEDs ER, RD and BA are blinking with a frequency of 1 Hz.
4. LEDs ER and BA go off after 5 seconds, and the set baud rate is stored.
5. Now set the node address 2 with the coding switch.
6. The set node address will be accepted after 5 seconds.
– LED RD goes off.
– The CAN gateway module changes to Pre−Operational status.
) Note!
The node address can be changed any time with the coding
switch. The setting is accepted after switching on the supply
voltage.
- I/O−System IP20 1
- Contents 10
- 1 Preface 11
- 1.1 The I/O system IP20 13
- How to use this System Manual 16
- Document history 17
- 1.2.3 Document history 17
- 1.3 Legal regulations 19
- Legal regulations 20
- Safety instructions 21
- Technical data 25
- The modular system 100
- The compact system 113
- EPM-T831 1A.10 127
- EPM-T833 1A.10 135
- 02413567 143
- Mechanical installation 147
- Electrical installation 155
- 8.1 Via system bus (CAN) 171
- 8.2 Network management (NMT) 173
- Network management (NMT) 174
- 8.3 Transmitting process data 175
- Transmitting process data 176
- PDO1-TX PDO1-RX 178
- 2. 3. 4 178
- Transmitting parameter data 188
- Telegram structure 188
- Identifier = 1538 190
- Identifier = 1410 190
- 8.6 Node Guarding 195
- Node Guarding 196
- 8.7 Heartbeat 197
- Heartbeat 198
- 8.8 Reset node 199
- 8.9 Monitoring 201
- Monitoring 202
- Digital output monitoring 202
- 8.10 Diagnostics 205
- Diagnostics 206
- Emergency telegram 206
- 8.10.1 Emergency telegram 206
- Status of the digital outputs 208
- Via the index I6401 209
- Via the index I6411 209
- Network via CANopen 211
- Networking via PROFIBUS−DP 255
- Commissioning 283
- 12.1 Important notes 295
- Parameterising analog modules 300
- Parameter data 300
- Diagnostic data 304
- 12.3.2 Diagnostic data 304
- 12.3−11 309
- 12.3−12 310
- 12.3−13 311
- 12.3−16 314
- 12.3−17 315
- 12.3−18 316
- Input data / output data 325
- 2 x 32 bit counter (mode 0) 326
- Encoder (modes 1, 3, and 5) 328
- Counter 0 332
- Counter 1 332
- 12.4−13 333
- 12.4−14 334
- 12.4−15 335
- 12.4−16 336
- 12.4−17 337
- 12.4−18 338
- 12.4−19 339
- 12.4−20 340
- 12.4−21 341
- 12.4−22 342
- 12.4−23 343
- 12.4−24 344
- 12.4−25 345
- 12.4−26 346
- 12.4−27 347
- 12.4−28 348
- 12.4−30 350
- 12.4−31 351
- 12.4−32 352
- 12.4−33 353
- 12.4−34 354
- 12.4−35 355
- 12.4−36 356
- 12.4−37 357
- 12.4−38 358
- 12.4−39 359
- 12.4−40 360
- 12.4−41 361
- 12.4−42 362
- 12.4−43 363
- 12.4−44 364
- 12.4−45 365
- 12.4−46 366
- 12.4−47 367
- 12.4−48 368
- 12.4−49 369
- 12.4−50 370
- 12.4−51 371
- 12.4−52 372
- 12.4−53 373
- 12.4−54 374
- 12.4−55 375
- 12.4−56 376
- Parameterising SSI interface 379
- EDSPM−TXXX−9.0−11/2009 384
- 12.5−11 387
- Encoder (mode 0) 395
- 12.6.3 Encoder (mode 0) 395
- 32 bit counter (mode 1) 397
- 12.6−10 400
- 12.6−11 401
- 12.6−12 402
- 12.6−13 403
- Measuring the period (mode 4) 404
- 12.6−15 405
- 12.8 Loading default setting 409
- · Example: 413
- 13.1−11 423
- 13.1−12 424
- 13.1−14 426
- 13.1−16 428
- 13.1−17 429
- 13.1−18 430
- Gateway Counter 438
- Data to module 438
- Data from module 438
- In3/In6 (DIR) 446
- 13.2−13 447
- 13.2−14 448
- 13.2−15 449
- Counter access 450
- 13.2−17 451
- 13.2−18 452
- 13.2−19 453
- 13.2−20 454
- 13.2−21 455
- 13.2−22 456
- 13.2−23 457
- 13.2−24 458
- 13.2−25 459
- 13.2−26 460
- 13.2−27 461
- 13.2−29 463
- 13.2−30 464
- 13.2−31 465
- 13.2−32 466
- 13.2−33 467
- 13.2−34 468
- 13.2−36 470
- 13.2−37 471
- 13.2−38 472
- 13.2−40 474
- In3/In6 (B) 475
- 13.2−42 476
- 13.2−43 477
- 13.2−44 478
- 13.2−46 480
- 13.2−47 481
- 13.2−48 482
- 13.2−49 483
- 13.2−50 484
- 13.2−52 486
- 13.2−54 488
- 13.2−55 489
- 13.3.1 Parameter data 491
- Gateway SSI-Interface 493
- 13.4.1 Parameter data 495
- Gateway Counter/Dig In 496
- 13.4.3 Encoder (mode 0) 498
- Signal characteristic 503
- 13.4−10 504
- 13.4−11 505
- 13.4−12 506
- 13.4−14 508
- 14.1 Fault messages 511
- Appendix 513
- 10987654321 544
Relacionado con productos y manuales para Hardware Lenze EPM−T9XX Modular system
Hardware Lenze E82MV752 4Bxxx Manual de usuario
(20 paginas)
(20 paginas)
Hardware Lenze EMZ9374IB Manual de usuario
(122 paginas)
(122 paginas)
Hardware Lenze EZN3x0060H054 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze EPM-H521 Manual de usuario
(136 paginas)
(136 paginas)
Hardware Lenze MC−xxx Card Manual de usuario
(46 paginas)
(46 paginas)
Hardware Lenze EWS1001 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Lenze EWS1003 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Lenze E93ZWLX Manual de usuario
(77 paginas)
(77 paginas)
Hardware Lenze EMZ2221IB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze E82ZMBRB Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze ECSCMxxx Manual de usuario
(375 paginas)
(375 paginas)
Hardware Lenze ECSZZxxxxxx Manual de usuario
(68 paginas)
(68 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales