Lenze E94AYCEP Manual de usuario descargar pdf (Pagina 110)

11 Parameter reference

11.3 Parameters of the communication module for slot MXI2

111

Lenze · E94AYCEP communication module (POWERLINK MN/CN) · Communication Manual · DMS 6.0 EN · 02/2014 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C14066

C14067

C14071

Parameter | Name:

C14066 | EPL CN: Max. user data PRes RPDO

Data type: UNSIGNED_16

Index: 10509 = 0x290D

EPL index: See subcodes

The code defines the reserved user data length of the PRes telegrams for Controlled Nodes 1 ... 100. Each subcode

number corresponds to one EPL node with the same node ID. The EPL node must be enabled via code C14028

The subcodes describe the PRes telegrams received. The value must be within the range of 36 ... 1490 bytes.

The values are upper limit values for the entire size of the PDO mappings for received PRes telegrams.

In the configured state, the values stored for the nodes must be identical to the corresponding C14072

entries.

C14066 must have an identical value in all EPL nodes of the network.

Setting range (min. value | unit | max. value)

0 Byte 1490

Subcodes Lenze setting Info EPL index

C14066/1 0 byte EPL CN: max. user data of RPDO 0x1F8D.0x01

... ... ... ...

C14066/100 0 byte EPL CN: max. user data of RPDO 0x1F8D.0x64

 Read access  Write access  CINH  PLC-STOP  No transfer  PDO_MAP_RX  PDO_MAP_TX  COM  MOT

Parameter | Name:

C14067 | EPL MN: time-out isochronous comm. CN

Data type: UNSIGNED_32

Index: 10508 = 0x290C

EPL index: See subcodes

The code defines the reserved user data length of the PRes frames for Managing Node, diagnostic device or router.

Each subcode number corresponds to one EPL node with the same node ID. The EPL node must be enabled via code

C14028

The subcode describes the PRes telegrams received. The value must be within the limits of 36 ... 1490 bytes.

The values are upper limit values for the entire size of the PDO mappings for received PRes telegrams.

In the configured state, the values stored for the nodes must be identical to the corresponding C14072

entries.

C14067 must have an identical value in all EPL nodes of the network.

Setting range (min. value | unit | max. value)

0 ns 4294967295

Subcodes Lenze setting Info EPL index

C14067/1 5000 ns EPL Time-out isochronous comm.

0x1F92.0x01

... ... ... ...

C14067/100 5000 ns EPL Time-out isochronous comm.

0x1F92.0x64

 Read access  Write access  CINH  PLC-STOP  No transfer  PDO_MAP_RX  PDO_MAP_TX  COM  MOT

Parameter | Name:

C14071 | EPL Max. PDO user data RPDO PReq

Data type: UNSIGNED_16

Index: 10504 = 0x2908

EPL index: 0x1F98.0x04

The code defines the maximum data volume to be received by the Controlled Node of the PDP mapping for the PReq

telegram to be defined via one of the codes C14231

... C14240.

In the configured state, the value must be identical to the entry for a response valid for the EPL node.

When a Servo Drive 9400 is used, the code as Managing Node is irrelevant since Servo Drives 9400 as Managing

Nodes only transmit PDO data via broadcast PRes telegrams (C14071 = 36 bytes).

Setting range (min. value | unit | max. value) Lenze setting

0 Byte 1490 36 bytes

 Read access  Write access  CINH  PLC-STOP  No transfer  PDO_MAP_RX  PDO_MAP_TX  COM  MOT

1 2 ... 105 106 107 108 109 110 111 112 113 114 115 ... 147 148

Comentarios a estos manuales

Sin comentarios

Lenze E94AYCEP Manual de usuario Pagina 110

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Lenze E94AYCEP