Lenze DSD Manual de usuario Pagina 447
- Pagina / 496
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23 447
18 Drive dimensioning messages
18.2 Drive system
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
18.2.8 Torque setting range yyy requires measures
18.2.9 Torque setting range yyy and tensile force setting range zzz require measures
Note!
For the selected winding control mode xxx and the torque setting range yyy, we recommend low-friction,
mechanical transmission elements between the motor and the winding shaft as well as a KTY sensor for
the compensation of the motor temperature.
Cause Effects Possible remedies
The torque setting range results from
the entered values for tensile force
and diameter.
Minimum tensile forces cannot be re-
alised without the recommended
measures.
• Carry out recommended meas-
ures.
Note!
For the selected winding control mode xxx, the torque setting range yyy and the tensile force setting range
zzz, we recommend low-friction, mechanical transmission elements between the motor and the winding
shaft as well as a KTY sensor for the compensation of the motor temperature.
Cause Effects Possible remedies
The torque setting range results from
the entered values for tensile force
and diameter.
Minimum tensile forces cannot be re-
alised without the recommended
measures.
• Carry out recommended meas-
ures.
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Relacionado con productos y manuales para Software Lenze DSD
Software Lenze Engineer v2.21 Manual de usuario
(312 paginas)
(312 paginas)
(270 paginas)
Software Lenze 8400 motec Manual de usuario
(518 paginas)
(518 paginas)
Software Lenze i700 Manual de usuario
(338 paginas)
(338 paginas)
Software Lenze 8400 TopLine Manual de usuario
(176 paginas)
(176 paginas)
Software Lenze 8400 StateLine Manual de usuario
(103 paginas)
(103 paginas)
Software Lenze 8400 HighLine Manual de usuario
(157 paginas)
(157 paginas)
Software Lenze 8400 BaseLine C Manual de usuario
(342 paginas)
(342 paginas)
Software Lenze 8400 BaseLine D Manual de usuario
(260 paginas)
(260 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.287 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales