Lenze EVS9332xK Manual de usuario descargar pdf (Pagina 49)

Function library

Function blocks

3.2.3 Function block CDATA

3−21

EDSVS9332K−EXT EN 4.0

Signal Source Note

Name Typ

DIS DIS format CFG List

CDATA−SEL a C1321/3 dec [abs] C1320/3 1 Profile selection, 0 = profile 0 (1st profile)

CDATA−SEL−CAM−MODE d C1323/15 bin C132215 2 HIGH: profile changeover while travelling the profile. Hence, clutch functions can

be implemented via profiles.

CDATA−HOLD d C1323/6 bin C1322/6 2 HIGH: prevents profile switching, input has priority over CDATA−RESET

CDATA−CYCLE d C1323/1 bin C1322/1 2 Automatic profile switching

LOW: profile selection from input CDATA−SEL is active

HIGH: the profiles from C1311 and C1312 are cyclically processed

CDATA−RESET d C1323/2 bin C1322/2 2 If CDATA−RESET = HIGH and CDATA−CYCLE = LOW, the input CDATA−SEL is

evaluated immediately

If CDATA−RESET = HIGH and CDATA−CYCLE = HIGH, the profile from C1311 is

processed

CDATA−LOAD d C1323/7 bin C1322/7 2 Loaded profiles accepted with LOW−HIGH edge

CDATA−TEACH d C1323/13 bin C1322/13 2 Teach function, contact Lenze

CDATA−REL−SEL d C1323/3 bin C1322/3 2 HIGH: feed function active (relative positioning)

CDATA−YIN ph C1325/6 dec [inc] C1324/6 3 Input for the teach function, contact Lenze

CDATA−OFFS−XIN ph C1325/7 dec [inc] C1324/7 3 Offset on input CDATA−XIN if C1338 = 1 has been selected

CDATA−XIN ph C1325/2 dec [inc] C1324/2 3 Input for master value position if C1332 = 1

CDATA−XOFFS ph C1325/3 dec [inc] C1324/3 3 Input for offset in X direction (only if C1332 = 0)

CDATA−X−START ph C1325/1 dec [inc] C1324/1 3 Input for the profile starting position on the X axis

CDATA−X−RESET d C1323/4 bin C1322/4 2 HIGH: sets the master value integrator to the value at input CDATA−X−START

CDATA−DFIN phd C1327/1 dec [rpm] C1326/1 4 Input for digital frequency if C1332 = 0

CDATA−XFACT a C1321/2 dec [%] C1320/2 1 Stretching/compression factor

+100 % = no compression/stretching, >100 % = compression,

<100 % = stretching

CDATA−TP−SPEED−LIM phd C1327/2 dec [rpm] C1326/2 4 Selection of a compensation speed. Input is activated via C1296.

It is impermissible to select constant values, e.g. via free codes (FCODE).

CDATA−TP−POS ph C1325/4 dec [inc] C1324/4 3 Touch probe position of the master value (only if C1332 = 0)

CDATA−TP−DISABLE d C1323/14 C1322/14 HIGH: suppression of touch probe

CDATA−X−TP/E5 d C1323/8 − − − Selection of the touch probe source (only for synchronisation)

LOW: source CDATA−X−TP

HIGH: terminal X5/E5

CDATA−X−TP d C1323/5 bin C1322/5 2 LOW−HIGH edge sets master value integrator to position of input CDATA−TP−POS

CDATA−TP−EDGE−SELECT d C1323/16 bin C1322/16 2 LOW: HIGH−LOW edge of the input signal at X5/E4 is evaluated.

HIGH: LOW−HIGH edge of the input signal at X5/E5 is evaluated.

CDATA−ACTCAM a Output of the active profile

CDATA−ERR−NR a Display of the error number from the teach function

CDATA−BUSY d LOW−HIGH edge: the interpolation point distribution is not optimal, select fewer

points

CDATA−BUSY−LENx d HIGH: CDATA−LENx and CDATA−Y−END are not valid and are being determined at

present (e.g. profile switching)

CDATA−LOAD−BUSY d HIGH: new profile data is being accepted at present, the controller is inhibited

(only if input CDATA−LOAD = HIGH)

CDATA−LOAD−RDY d Handshake signal for reloading profiles

CDATA−LOAD−ERR d HIGH: error in the current profile at check via C0500

CDATA−LOAD−ERR−NR d HIGH: error in the current profile at check via C0500

CDATA−CHK−ERR d HIGH: the checksum transferred to C0509 does not correspond to the profile data

CDATA−CHK−BUSY d HIGH: profile checksum checking is active and not yet completed

CDATA−X0 d LOW−HIGH edge: zero crossing of the master value integrator

CDATA−X<0 d HIGH: number range exceeded in X direction

CDATA−X>XMAX d HIGH: number range exceeded in X direction

CDATA−SEC1

d HIGH: section 1 active

CDATA−SEC2

d HIGH: section 2 active

CDATA−SEC3

d HIGH: section 3 active

CDATA−SEC4

d HIGH: section 4 active

CDATA−SEC5

d HIGH: section 5 active

CDATA−X0−CYCLE d LOW−HIGH edge:zero crossing of the master value integrator when a profile cycle

from C1311 and C1312 is processed.

CDATA−TEACH−BUSY d Teach function, contact Lenze

CDATA−TEACH−ACTIVE d Teach function, contact Lenze

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 385 386

Comentarios a estos manuales

Sin comentarios

Lenze EVS9332xK Manual de usuario Pagina 49

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Lenze EVS9332xK