Lenze PLC Designer ApplicationTemplate (PLC Designer R3- Manual de usuario Pagina 93
- Pagina / 177
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Lenze · ApplicationTemplate · 1.3 EN - 04/2013 93
Architecture: The ApplicationTemplate in detail
Error handling
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
More information:
L_EATP_ErrorSet
( 119)
L_EATP_ModuleErrorHandler ( 124)
9.9.2 Configuring an error response
The error response types of the error handler define the state of the module's intrinsic application.
If an error occurs, the standard behaviour triggers the configured error response in the other
machine modules.
If a different error response of the machine module is desired, the possibility of programming the
desired error response in the corresponding machine module is provided.
• Further information on the DefaultCoupling (predefined standard response) can be found in the
following section: Default coupling
( 83)
• The error states that can be defined in the module applications (MAP) are divided into the
following error categories:
9.9.3 Acknowledging errors
The acknowledgement of errors deletes all error messages / error causes that have been defined as
requiring acknowledgement
from the current error list (Error List).
The acknowledgement of errors can be activated by the following procedures:
1. Permanent activation: Within the module application via the following program command:
Error text Text description of the error. The (English) error text is stored in the table of
attributes.
The error text always is to be used if no
higher-level
mechanism for implementation of the error number
in national languages is activated (example: higher-
level visualization).
Detailed
error information
For each error, an additional
attribute (type: DWORD) can be
used, which (in connection with the
error number) can be interpreted.
For a "Drive Error" group error, for instance, the
detailed error information of the corresponding
controller can be used.
Priority Assign priority for errors of the same error response type.
Characteristic Description Further information
Error response (in order of ascending
priority)
Description / acknowledgement behaviour
Information Writes information in the logbook of the controller.
• No acknowledgement required.
Quick stop (fault) Error response in the case of which the machine module involved changes to
the "Stop" status.
• The acknowledgement behaviour is parameterisable.
Warning The machine module/the application remains in the same status.
• The acknowledgement behaviour is parameterisable.
Error Causes the machine module involved to trip a response (for example setting
controller inhibit/pulse inhibit).
• The acknowledgement behaviour is parameterisable.
System fault Fatal error.
Restart of the application required (by mains switching or device reset).
• No acknowledgement possible.
- PLC Designer 1
- Contents 2
- Pictograph and signal word! 10
- About this documentation 11
- Danger! 12
- Requirements 13
- ( 110) 15
- 4.3.2 Machine modules (MM) 18
- 4.3.6 State machine 21
- 4.3.7 Error handling 22
- Note! 33
- State machine 35
- State machine ( 21) 36
- ( 119) 36
- [8-4] Example: App1 64
- 8.11 Online change 68
- Vis.diPieces := 4711; 72
- ( 127) 73
- 9.3 State machine 77
- State machine 80
- 9.4 Default coupling 83
- 9.9 Error handling 92
- 9.9.1 Defining errors 92
- 9.9.3 Acknowledging errors 93
- ÊTRUE. The 94
- ( 124) 94
- 9.10 Triggering errors 95
- How to write the CSV file: 96
- 9.13 Logbook 97
- 9.14 Module diagnostics 97
- 9.15 Multitasking 98
- 9.16 Consistent data transfer 99
- 9.17 Internal Control 101
- How to proceed: 105
- 11.2.1 L_EATP_Application 115
- 11.2.2 L_EATP_CriticalSection 117
- 11.2.4 L_EATP_ErrorSet 119
- 11.2.4.2 Acknowledging errors 120
- 11.2.5 L_EATP_Module 121
- 11.2.5.1 Base() 121
- 11.2.6 RegisterACD() 122
- 11.2.7 setCompIDAndVersion() 122
- 11.2.8 L_EATP_ModuleDiag 123
- 11.2.10 L_EATP_ModulRelations 125
- 11.2.11 L_EATP_SMAccess 126
- 11.3 2_Structs_Types 127
- 11.3.1 L_EATP_ACD_Base 127
- 11.3.2 L_EATP_BaseChannel 128
- 11.3.3 L_EATP_ErrorList 128
- 11.3.4 L_EATP_ErrorListEntry 128
- 11.3.5 L_EATP_MM_Address 129
- 11.3.6 L_EATP_MVis 129
- 11.3.7 L_EATP_scBase 129
- 11.4 3_Enums 129
- 11.4.2 L_EATP_SMStates 130
- Appendix 131
- How to proceed: 155
- Select Copy Empty 156
- Insert Empty Module 156
- )(('%$ 176
- 109 87654321 177
Relacionado con productos y manuales para Software Lenze PLC Designer ApplicationTemplate (PLC Designer R3-
(270 paginas)
Software Lenze 8400 motec Manual de usuario
(518 paginas)
(518 paginas)
Software Lenze i700 Manual de usuario
(338 paginas)
(338 paginas)
Software Lenze 8400 TopLine Manual de usuario
(176 paginas)
(176 paginas)
Software Lenze 8400 StateLine Manual de usuario
(103 paginas)
(103 paginas)
Software Lenze 8400 HighLine Manual de usuario
(157 paginas)
(157 paginas)
Software Lenze 8400 BaseLine C Manual de usuario
(342 paginas)
(342 paginas)
Software Lenze 8400 BaseLine D Manual de usuario
(260 paginas)
(260 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales