Lenze CANopen control technology Manual de usuario Pagina 71
- Pagina / 105
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DMS 4.2 EN 07/2011 TD17 L 71
Control technology | CANopen communication manual
Commissioning the CANopen Logic bus
Preparing the restart
Automatic with factory adjustment:
With an automatic restart, a factory adjustment is executed.
– Enter all required parameter values in the Control Configuration under the Service
Data Objects tab.
– Set the checkmark at "Reset Node" in order that the control executes the factory
adjustment. This causes the I/O system to change to the "Lenze System Bus" mode
and remains there.
– Program a "Reset Node" in your program code. Do not
use the SDO "Reset Node"
under the Service Data Objects tab. Otherwise the initialisation will be repeated
endlessly.
– After changing the I/O system:
Set the node address and baud rate at the coding switch for the CANopen mode and
then start the control.
8.9.4 Special features of the I/O-System 1000 (EPM-Sxxx)
There are different viable strategies for the I/O system restart:
Automatic:
You want the control to automatically initialise the I/O system after the device has
been replaced.
– Enter all required parameter values in the Control Configuration under the Service
Data Objects tab.
– Go to the Parameters tab and do not
set a checkmark at "Reset Node" in order that
the control does not execute a factory adjustment.
– Go to the Parameters tab and set a checkmark at Create all SDOs in order that the
control initialises all parameters.
– After changing the I/O system:
Set the node address and baud rate at the coding switch and then start the control.
Using the »Engineer«:
1. You have implemented the I/O system successfully into the PLC program.
2. You have parameterised some CANopen indexes of the I/O system using the
»Engineer«.
3. You do not want to transmit the parameter setting to the control configuration now,
since you can assume that after a possible device replacement a project planning tool
will be available.
– Operate the I/O system in CANopen mode.
– Go to the Parameters tab and do not
set a checkmark at "Reset Node" in order that
the control does not execute a factory adjustment.
– Save the »Engineer« project near the machine.
– After changing the I/O system:
Set the node address and baud rate at the coding switch and transmit the archived
parameter setting to the I/O system. Then start the control.
- PC-based Automation 1
- L-force Controls 1
- Contents 3
- Correction 5
- Task utilisation 5
- DMS 4.2 EN 07/2011 TD17 L 7 7
- About this documentation 9
- Conventions used 9
- 1.2 Conventions used 9
- L DMS 4.2 EN 07/2011 TD17 10
- Pictograph and signal word! 11
- Danger! 12
- DMS 4.2 EN 07/2011 TD17 L 13 13
- 4 System bus (CAN) / CANopen 15
- System bus (CAN) / CANopen 17
- 4.1.2 Field devices 17
- MC-CAN2-001 18
- DMS 4.2 EN 07/2011 TD17 L 19 19
- DMS 4.2 EN 07/2011 TD17 L 21 21
- CAN gateway 22
- CANopen bus 22
- DMS 4.2 EN 07/2011 TD17 L 23 23
- DMS 4.2 EN 07/2011 TD17 L 25 25
- DMS 4.2 EN 07/2011 TD17 L 27 27
- DMS 4.2 EN 07/2011 TD17 L 29 29
- Planning the CANopen network 31
- DMS 4.2 EN 07/2011 TD17 L 35 35
- 7 Preparing the field devices 37
- DMS 4.2 EN 07/2011 TD17 L 39 39
- DMS 4.2 EN 07/2011 TD17 L 41 41
- DMS 4.2 EN 07/2011 TD17 L 43 43
- DMS 4.2 EN 07/2011 TD17 L 45 45
- DMS 4.2 EN 07/2011 TD17 L 47 47
- DMS 4.2 EN 07/2011 TD17 L 49 49
- DMS 4.2 EN 07/2011 TD17 L 51 51
- DMS 4.2 EN 07/2011 TD17 L 53 53
- Creating a PLC program 55
- 4. Create a block: 55
- DMS 4.2 EN 07/2011 TD17 L 57 57
- DMS 4.2 EN 07/2011 TD17 L 59 59
- DMS 4.2 EN 07/2011 TD17 L 61 61
- ( 62) 63
- DMS 4.2 EN 07/2011 TD17 L 65 65
- DMS 4.2 EN 07/2011 TD17 L 67 67
- DMS 4.2 EN 07/2011 TD17 L 69 69
- DMS 4.2 EN 07/2011 TD17 L 71 71
- DMS 4.2 EN 07/2011 TD17 L 73 73
- DMS 4.2 EN 07/2011 TD17 L 75 75
- DMS 4.2 EN 07/2011 TD17 L 77 77
- DMS 4.2 EN 07/2011 TD17 L 79 79
- DMS 4.2 EN 07/2011 TD17 L 81 81
- DMS 4.2 EN 07/2011 TD17 L 83 83
- 10 CANopen with PROFIBUS 85
- DMS 4.2 EN 07/2011 TD17 L 87 87
- How to optimise the system: 91
- DMS 4.2 EN 07/2011 TD17 L 93 93
- DMS 4.2 EN 07/2011 TD17 L 95 95
- Parameter reference 97
- 15 Appendix 99
- DMS 4.2 EN 07/2011 TD17 L 101 101
- 16 Index 103
- 109 87654321 105
Relacionado con productos y manuales para Hardware Lenze CANopen control technology
Hardware Lenze E82ZAFCC001 Manual de usuario
(82 paginas)
(82 paginas)
Hardware Lenze E82ZAFCC010 Manual de usuario
(84 paginas)
(84 paginas)
Hardware Lenze EMF2178IB Manual de usuario
(154 paginas)
(154 paginas)
Hardware Lenze E82ZAFCC100 Manual de usuario
(96 paginas)
(96 paginas)
Hardware Lenze E82ZAFCC200 Manual de usuario
(94 paginas)
(94 paginas)
Hardware Lenze E82ZAFCC210 Manual de usuario
(96 paginas)
(96 paginas)
Hardware Lenze E82ZAFUC001 Manual de usuario
(108 paginas)
(108 paginas)
Hardware Lenze EMF2174IB Manual de usuario
(17 paginas)
(17 paginas)
Hardware Lenze E82ZAFUC010 Manual de usuario
(114 paginas)
(114 paginas)
Hardware Lenze EMF2176IB_ Manual de usuario
(30 paginas)
(30 paginas)
Hardware Lenze MC-CAN2 Manual de usuario
(32 paginas)
(32 paginas)
Hardware Lenze EMF2178IB Manual de usuario
(118 paginas)
(118 paginas)
Hardware Lenze 931M-931W Manual de usuario
(158 paginas)
(158 paginas)
Hardware Lenze E82ZAFFC001 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze E82ZAFFC010 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze 931K Manual de usuario
(148 paginas)
(148 paginas)
Hardware Lenze E82ZBS020 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Lenze MDFQA Manual de usuario
(32 paginas)
(32 paginas)
Hardware Lenze DDS v2.1 Manual de usuario
(41 paginas)
(41 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales