Lenze Engineer v2.21 Manual de usuario Pagina 252
- Pagina / 312
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Error messages
Communication entity generator
252
Lenze · Engineer · 2.13 EN - 10/2014
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
12.4.2 Compact (8200)
Unexpected error [CECOMP0001]
Different transfer modes for CAN1 IN/OUT [CECOMP0002]
COB-ID {0} has been assigned several times for nodes [CECOMP0003]
Baud rate of {0}k is not supported by node [CECOMP0004]
Error during writing on object [CECOMP0005]
Response (Lenze setting printed in bold)
Error Warning Information
Cause Remedy
Response (Lenze setting printed in bold)
Error Warning Information
Cause Remedy
The transfer modes have been coupled for the CAN1
objects of the controller.
CAN1-IN and CAN1-OUT have to be transferred in a
synchronised manner or asynchronously.
The following combinations are permissible:
CAN1-IN CAN1-OUT
Synchronous Synchronous
Asynchronous Time or event
Response (Lenze setting printed in bold)
Error Warning Information
Cause Remedy
Assigning the same COB-ID several times for fixed
process data objects is not allowed for a 9300.
Ensure that no ports of a 9300 device are connected to
each other in the function block editor.
By this, the ports would receive the same COB-IDs.
Response (Lenze setting printed in bold)
Error Warning Information
Cause Remedy
The baud rate cannot be transferred to the associated
code.
Response (Lenze setting printed in bold)
Error Warning Information
Cause Remedy
Object could not be written.
- Engineer 1
- Contents 3
- About this documentation 10
- User interface 13
- Safety instructions ( 12) 16
- 4.1 Creating a new project 31
- ( 51) 34
- Next steps 38
- 4.2 Opening the project file 38
- 4.4 Updating catalogues 40
- 4.5 Project properties 41
- 4.6 Save a project 42
- 4.7.1 Saving an archive 43
- 4.7.2 Open an archive 44
- Inserting an axis ( 48) 45
- How to insert an axis: 48
- 5.2 Inserting components 51
- Inserting controllers ( 53) 51
- Inserting a motor ( 58) 51
- 5.2.1 Inserting controllers 53
- 5.2.2 Inserting application 55
- How to insert a motor: 58
- How to add an I/O system: 60
- 5.2.6.1 System 1000 61
- Inserting components 65
- How to add a gearbox: 67
- How to replace a component: 71
- How to update the project: 76
- 6.2 Going online 77
- ( 79) 78
- ( 22) 78
- ( 81) 79
- 6.2.1.1 Diagnostic adapter 80
- 6.2.1.2 CAN 81
- 6.2.1.4 PROFIBUS 84
- 6.2.1.5 PROFINET 85
- 6.3 Going offline 96
- 6.4 System bus configurator 96
- Inverter 98
- Drives 8400 98
- Servo Drives 98
- Controller I/O system 98
- 7.1 Options 99
- Danger! 100
- area has 104
- 7.3.3 Upload parameter set 106
- 7.3.4 Save parameter set 107
- How to start the function: 109
- 7.6 Diagnostics 110
- 7.7 Data logger 111
- 7.7.1 User interface 112
- 7.7.1.1 Data logger toolbar 112
- 7.7.1.2 Diagram 113
- 7.7.1.3 Vertical settings 114
- 7.7.1.5 Horizontal settings 115
- 7.7.1.6 Recording settings 115
- 7.7.2 Operation 116
- How to change a selection: 117
- Trigger event 118
- (negative) 118
- Trigger level 118
- (positive) 119
- 7.7.2.8 Comparing peak values 121
- 7.7.3 Data records 122
- 7.7.3.6 Overlay function 126
- 7.8 Oscilloscope 127
- 8.2 Terminology used 129
- ( 186) 130
- ( 132) 131
- ( 173) 131
- 8.6.1 Terminology used 134
- ( 77) 137
- Icon Function 141
- 8.7 Copying parameter sets 143
- & gain) in each case 145
- 8.10.1 Connecting FBs 151
- Shortcut Function 153
- 8.11 Port editor (ports) 155
- 8.11.1.4 Record or Simple? 160
- 9400 HighLine 1 161
- 9400 HighLine 2 161
- How to add a port: 162
- ( 163) 163
- ( 165) 163
- ( 162)" 163
- ( 168) 163
- ( 166) 164
- ( 179) 168
- How to rename a port: 169
- How to delete a port: 169
- How to show the user menu: 170
- ( 177) 174
- ( 175) 174
- 8.13.2 Port interconnection 175
- ( 155) 179
- ( 180) 179
- ( 181) 179
- 8.13.5.1 Automatic connection 180
- 8.13.5.2 Manual connection 180
- 8.13.5.4 Mixed connection 182
- Main drive (master) 183
- Mark track on the material 184
- ( 190) 186
- ( 191) 186
- ( 193) 186
- 8.14.5 Measuring systems 194
- Positive feed Negative feed 196
- Feed (lift) = cycle 196
- Y = position of the axis 196
- X = master value/master angle 196
- 9.1.1 Application level 203
- ( 226) 204
- ( 128) 204
- 9.1.2 Network level 205
- ( 207) 206
- ( 210) 206
- ( 216) 206
- How to insert a network: 207
- 9.3.1 Nodes 210
- Diagnostics 210
- 9.3.1.1 Inserting nodes 212
- 9.3.1.2 Node settings 214
- 9.3.1.3 Removing nodes 214
- 9.3.2 Settings 215
- 9.3.3 Product features 215
- 9.3.4 Diagnostics 215
- 9.4 CAN network 216
- 9.4.1 Nodes 216
- 9.4.1.1 Inserting nodes 218
- 9.4.1.2 Node settings 219
- 9.4.1.3 Removing nodes 220
- 9.4.2 Settings 221
- 9.4.3 Synchronisation 223
- 9.4.4 CAN objects 225
- 9.4.5 Product features 225
- 9.5 Process data objects 226
- Application examples 228
- 11.2 Catalogue packages 233
- [11-2] Catalogues dialog box 234
- 11.5.1 Objects of versioning 236
- Error messages 238
- Overview 257
- 13.1 "File" menu 258
- 13.2 "Edit" menu 259
- 13.3 "Insert" menu 260
- 13.4 "View" menu 260
- 13.5 "Online" menu 260
- 13.7 "Tools" menu 263
- 13.8 "?" menu 263
- "?" menu 264
- Appendix 266
- How to proceed: 283
- How to save a user motor: 296
- How to insert a user motor: 297
- How to delete a user motor: 302
- How to export a user motor: 303
- How to import a user motor: 304
- Glossary 305
- )(('%$& 311
- 109 87654321 312
Relacionado con productos y manuales para Software Lenze Engineer v2.21
(270 paginas)
Software Lenze 8400 motec Manual de usuario
(518 paginas)
(518 paginas)
Software Lenze i700 Manual de usuario
(338 paginas)
(338 paginas)
Software Lenze 8400 TopLine Manual de usuario
(176 paginas)
(176 paginas)
Software Lenze 8400 StateLine Manual de usuario
(103 paginas)
(103 paginas)
Software Lenze 8400 HighLine Manual de usuario
(157 paginas)
(157 paginas)
Software Lenze 8400 BaseLine C Manual de usuario
(342 paginas)
(342 paginas)
Software Lenze 8400 BaseLine D Manual de usuario
(260 paginas)
(260 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales