Lenze DDS System bus CAN for PLC Manual de usuario Pagina 109
- Pagina / 178
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System bus (CAN) for Lenze PLC devices
CAN system blocks
7.6 CAN_Management (node number: 101)
7−21
L
PLC−Systembus EN 2.0
7.6.2 Outputs_CAN_Management
Variable Data type Signal type Address Display
code
Display
format
Notes
CAN_bResetNode_b
Bool Binary
%QX101.0.0
− −
Carry out reset node of the PLC
CAN_bTxCan2Synchronized_b %QX101.0.1 Transmit CAN2_OUT with sync
telegram.
CAN_bTxCan3Synchronized_b %QX101.0.2 Transmit CAN3_OUT with sync
telegram.
Note!
If CAN_bTxCan2Synchronized_b and/or CAN_bTxCan3Synchronized_b are integrated, it is required
to configure the device as sync transmitter. The data are transmitted immediately after the sync
signal is sent.
7.6.3 Activating a reset node
A reset node is activated by setting CAN_bResetNode_b to TRUE or C0358 = 1.
Tip!
Even if the CAN_Management SB has not been assigned to the control configuration, a reset node
can be activated via C0358.
(^ 3−8)
7.6.4 Defining the instant of transmission for CAN2_OUT/CAN3_OUT
Via CAN_bTxCan2Synchonized_b and CAN_bTxCan3Synchonized_b you define the instant of
transmission for the CAN objects CAN2_OUT and CAN3_OUT:
· FALSE: Data from CAN2_OUT/CAN3_OUT are sent at the end of the process image.
· TRUE: Data from CAN2_OUT/CAN3_OUT are sent to sync.
– The identifiers for the sync transmission C0369 and reception telegram can be set via
C0367/C0368.
– The sync Tx time can be set via C0369.
– Detailed information on this can be found in the description of the CAN_Syncronization SB.
(^ 7−23)
- Global Drive 1
- System bus (CAN) 1
- Contents 4
- 1.1 About this Manual 9
- · "Via wDrvNr..." 10
- 1.1.4 Terminology used 12
- 2.1 Introduction 13
- General information 14
- 2.4.1 Identifier 15
- 2.4.2 User data 17
- 2.5 Network management (NMT) 18
- 2.6.1 Process data channels 19
- 2.6.3 Process data telegram 22
- 2.7.1 Parameter data telegram 23
- 2.7.1.1 Identifier 23
- 2.7.1.2 Command code 24
- 2.8 Free CAN objects 31
- 2.10 Monitoring mechanisms 33
- NMT Master NMT Slave 34
- 3.1 CAN baud rate 35
- 3.2 CAN boot−up 36
- 3.3 Node address (node ID) 37
- 3.7 Synchronisation 41
- 3.8 Reset node 42
- 3.9 System bus management 42
- 3.10 Mapping indexes to codes 42
- 3.12 Monitoring processes 45
- 3.13 Diagnostics 47
- 3.13.2 Telegram counter 48
- 3.13.3 Bus load by the PLC 49
- 4.1 CAN baud rate 51
- 4.2 CAN boot−up 52
- 4.3 Node address (node ID) 53
- Configuration (AIF interface) 54
- 4.6 Synchronisation 57
- 4.7 Reset node 58
- 4.8 Monitoring processes 58
- 4.8.2 Bus off 59
- 4.9 Diagnostics 60
- 5.1 CAN baud rate 61
- 5.2 CAN boot−up 62
- 5.3 Node address (node ID) 63
- Configuration (FIF interface) 64
- 5.7 Synchronisation 67
- 5.8 Reset node 68
- 5.9 System bus management 68
- 5.10 Monitoring processes 69
- 5.11 Diagnostics 71
- 5.11.2 Telegram counter 72
- 5.11.3 Bus load by FIF−CAN 73
- 6.1 CAN baud rate 75
- 6.2 CAN boot−up 76
- 6.3 Node address (Node ID) 77
- 6.7 Synchronisation 81
- 6.8 Reset node 82
- 6.9 System bus management 82
- 6.10 Monitoring processes 83
- 6.11 Diagnostics 85
- 6.11.2 Telegram counter 86
- 6.11.3 Bus load by CAN−AUX 87
- 7 CAN system blocks 89
- 7.1.1 Inputs_CAN1 90
- 7.1.2 Outputs_CAN1 90
- 7.1.3 Process data telegram 91
- 7.2.1 Inputs_CAN1 95
- 7.2.2 Outputs_CAN1 95
- 7.2.3 Process data telegram 96
- 7.3.1 Inputs_CAN1 99
- 7.3.2 Outputs_CAN1 99
- CAN system blocks 100
- 7.3.3 Process data telegram 100
- 7.4 CAN2_IO (node number: 32) 102
- 7.4.1 Inputs_CAN2 103
- 7.4.2 Outputs_CAN2 103
- 7.4.3 Process data telegram 103
- 7.5 CAN3_IO (node number: 33) 105
- 7.5.1 Inputs_CAN3 106
- 7.5.2 Outputs_CAN3 106
- 7.5.3 Process data telegram 106
- 7.6.1 Inputs_CAN_Management 108
- PLC−Systembus EN 2.0 109
- 7.6.5 Status messages 110
- FIF−CAN system blocks 117
- 8.1.1 FIF_Inputs_CAN1 118
- 8.1.2 FIF_Outputs_CAN1 118
- 8.1.3 Process data telegram 119
- 8.2.1 FIF_Inputs_CAN2 122
- 8.2.2 FIF_Outputs_CAN2 122
- 8.2.3 Process data telegram 122
- 8.3.1 FIF_Inputs_CAN3 125
- 8.3.2 FIF_Outputs_CAN3 125
- 8.3.3 Process data telegram 125
- 8.4.5 Status messages 129
- CAN−AUX system blocks 130
- 9.1.1 Inputs_CANaux1 131
- 9.1.2 Outputs_CANaux1 131
- 9.1.3 Process data telegram 132
- 9.2.1 Inputs_CANaux2 135
- 9.2.2 Outputs_CANaux2 135
- 9.2.3 Process data telegram 135
- 9.3.1 Inputs_CANaux3 138
- 9.3.2 Outputs_CANaux3 138
- 9.3.3 Process data telegram 138
- 9.4.5 Status messages 142
- 10.1 Overview 143
- L_CanInit 144
- · Not for Drive PLC! 146
- Transmit status (nState) 151
- · See the following table 154
- 11.1 Overview 157
- · Invalid for bit 0 = 1 161
- L_CanDSxHeartBeat 164
- L_CanDSxNodeGuarding 168
- NodeLifeTimeFactor (C0383) 170
- Guarding" 171
- L PLC−Systembus EN 2.0 173
- 12 Index 173
- XCAN sync identifier, 4−7 178
- XCAN sync response, 4−7 178
Relacionado con productos y manuales para Hardware Lenze DDS System bus CAN for PLC
Hardware Lenze E82ZAFFC001 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze E82ZAFFC010 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze 931K Manual de usuario
(148 paginas)
(148 paginas)
Hardware Lenze E82ZBS020 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Lenze MDFQA Manual de usuario
(32 paginas)
(32 paginas)
Hardware Lenze DDS v2.1 Manual de usuario
(41 paginas)
(41 paginas)
Hardware Lenze E82ZWBRU Manual de usuario
(63 paginas)
(63 paginas)
Hardware Lenze 8615E Manual de usuario
(126 paginas)
(126 paginas)
Hardware Lenze E82ZAFAC001 Manual de usuario
(66 paginas)
(66 paginas)
Hardware Lenze E94P Manual de usuario
(1 paginas)
(1 paginas)
Hardware Lenze ELM3−010H010 Manual de usuario
(48 paginas)
(48 paginas)
Hardware Lenze E82ZM113-001 Manual de usuario
(58 paginas)
(58 paginas)
Hardware Lenze E82ZBU Manual de usuario
(18 paginas)
(18 paginas)
Hardware Lenze DDS v2.0 Manual de usuario
(26 paginas)
(26 paginas)
Hardware Lenze DDS v2.3 Manual de usuario
(340 paginas)
(340 paginas)
Hardware Lenze 8615E Manual de usuario
(158 paginas)
(158 paginas)
Hardware Lenze E82ZAFAC010 Manual de usuario
(66 paginas)
(66 paginas)
Hardware Lenze E82ZBC Manual de usuario
(102 paginas)
(102 paginas)
Hardware Lenze E94P v2.0 Manual de usuario
(9 paginas)
(9 paginas)
Hardware Lenze DDS v1.1 Manual de usuario
(11 paginas)
(11 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales