Lenze E84DGFCR Manual de usuario Pagina 71
- Pagina / 90
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
EDS84DMOTPNET EN 2.0 - 11/2011 L 71
Communication manual 8400 motec PROFINET
Error messages
Possible causes and remedies
PROFINET: Record Parameter: Invalid read [0x01bc6501]
PROFINET: Record Parameter: Invalid write [0x01bc6502]
PROFINET: Data output status bad [0x01bc6503]
PROFINET: Data_Exchange status quit [0x01bc6531]
PROFINET: Station name error [0x01bc6532]
PROFINET: IP address error [0x01bc6533]
Response (Lenze setting printed in bold) Setting: not possible
None System fault Fault Trouble Quick stop by trouble : Warning locked Warning Information
Cause Remedy
Invalid parameter read access Check configuration.
Response (Lenze setting printed in bold) Setting: not possible
None System fault Fault Trouble Quick stop by trouble : Warning locked Warning Information
Cause Remedy
Invalid parameter write access
When reading back data, the IO controller requested a
too short data length (number of data bytes).
Check configuration.
Response (Lenze setting printed in bold) Setting: not possible
None System fault Fault Trouble Quick stop by trouble : Warning locked Warning Information
Cause Remedy
• Output data invalid.
• Connection to Siemens S7 has been interrupted.
• Check cables and terminals.
• Connect network cable to PROFINET connections.
Response (Lenze setting printed in bold) Setting: C13880/1 (; Adjustable response)
: None System fault ; Fault Trouble ; Quick stop by trouble ; Warning locked Warning ; Information
Cause Remedy
The data exchange via PROFINET has been terminated.
• See also chapter "Interruption of PROFINET
communication" ( 62).
• Check cables and terminals.
• Connect network cable to PROFINET connections.
Response (Lenze setting printed in bold) Setting: not possible
None System fault : Fault Trouble Quick stop by trouble Warning locked Warning Information
Cause Remedy
Station name is not DNS-conform. Use DNS-conform station name.
Setting the station name
( 28)
Response (Lenze setting printed in bold) Setting: not possible
None System fault : Fault Trouble Quick stop by trouble Warning locked Warning Information
Cause Remedy
An invalid IP address has been assigned by the I/O
controller via PROFINET or has been set in code C13000
.
• Make sure that the I/O controller has assigned a valid
IP address via PROFINET.
• Set a valid IP address.
Setting the IP configuration
( 30)
- 8400 motec 1
- L-force Communication 1
- Contents 3
- 1 About this documentation 5
- version Description 7
- About this documentation 8
- Conventions used 8
- 1.2 Conventions used 8
- Terminology used 9
- 1.3 Terminology used 9
- Pictograph and signal word! 10
- Danger! 11
- 3 Product description 13
- Product description 15
- Connections and interfaces 15
- 4 Technical data 17
- 5 Installation 20
- Installation 21
- Mechanical installation 21
- 5.1 Mechanical installation 21
- E94YCER005 22
- E94YCER006 22
- Electrical installation 23
- Switch / switch 23
- I/O controller / I/O device 23
- 6 Commissioning 26
- ( 64)) 28
- ( 31) 30
- ( 33) 30
- ( 72) is output 30
- Byte 3 Byte 2 Byte 1 Byte 0 33
- 1 0 168 192 33
- ( 30)) 35
- ( 25) 37
- ( 28) 37
- ( 30) 37
- 7 Data transfer 38
- 8 Process data transfer 39
- Process data transfer 41
- 9 Parameter data transfer 45
- IO controller 46
- IO device 46
- [9-3] PROFINET data telegram 47
- Value No subindex 51
- Parameter data transfer 52
- Parameter format 54
- Parameter value 54
- Response head 56
- Error code 56
- Error information (error) 59
- 9.4 Error information (error) 59
- 10 Monitoring 62
- ( 69) is output 63
- 11 Diagnostics 64
- Diagnostics 65
- LED status displays 65
- 12 Error messages 68
- Error messages 70
- Possible causes and remedies 70
- 13 Parameter reference 73
- Parameter reference 75
- Table of attributes 86
- 14 Index 87
- 109 87654321 90
Relacionado con productos y manuales para Hardware Lenze E84DGFCR
Hardware Lenze E84DZMAWE1 Manual de usuario
(6 paginas)
(6 paginas)
Hardware Lenze E84DGFCG Manual de usuario
(149 paginas)
(149 paginas)
Hardware Lenze E84DGFCA Manual de usuario
(74 paginas)
(74 paginas)
Hardware Lenze GSS Manual de usuario
(80 paginas)
(80 paginas)
Hardware Lenze GKK Manual de usuario
(32 paginas)
(32 paginas)
Hardware Lenze g500 Manual de usuario
(36 paginas)
(36 paginas)
Hardware Lenze E82ZAFPC001 Manual de usuario
(100 paginas)
(100 paginas)
Hardware Lenze E82ZAFPC010 Manual de usuario
(106 paginas)
(106 paginas)
Hardware Lenze EMF2133IB Manual de usuario
(104 paginas)
(104 paginas)
Hardware Lenze E82ZAFPC201 Manual de usuario
(118 paginas)
(118 paginas)
Hardware Lenze MC-PBS Manual de usuario
(42 paginas)
(42 paginas)
Hardware Lenze 2130IB Manual de usuario
(92 paginas)
(92 paginas)
Hardware Lenze 2131IB Manual de usuario
(60 paginas)
(60 paginas)
Hardware Lenze EMF2112IB Manual de usuario
(53 paginas)
(53 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.180 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales