Lenze MC3000 Series Drives Manual de usuario descargar pdf (Pagina 10)

7 RG-MCMET

N2 Points

4.1 Metasys N2 Point Map

Table 3: Metasys N2 Point Map for MC3000 Series Drives

Point

Type

Point

Description (Point Name) Read (R)/

Override (R/O)

Point

Units

Decimal

Places

MIN

Value

MAX

Value

Default

Value

1 1 Parameter Version R -- 0 -- -- 143

1 2 Software Version R -- 0 -- -- 043

1 3 Software Revision R -- 0 -- -- 05

1 4 Drive Conﬁg/Size R -- 0 0 57 --

1 5 Drive Class R -- 0 -- -- 65

1 6 Total Runtime (RUNTIME HRS) R hrs 0 0 --

1 7 Total Runtime (RUNTIME MIN) R min 0 0 --

1 8 Operational Status (RUN STATUS) R -- 0 0 10 --

1 9 Load Percent (LOAD PERCENT) R % 0 150 180 180

1 10 Motor Voltage (MOTOR VOLTS) R VAC 0

1 11 Present Fault (FAULT) R -- 0 0 23 0

1 12 Recorded Fault 1 R -- 0 0 23 0

1 13 Recorded Fault 2 R -- 0 0 23 0

1 14 Recorded Fault 3 R -- 0 0 23 0

1 15 Recorded Fault 4 R -- 0 0 23 0

1 16 Recorded Fault 5 R -- 0 0 23 0

1 17 Recorded Fault 6 R -- 0 0 23 0

1 18 Recorded Fault 7 R -- 0 0 23 0

1 19 Recorded Fault 8 R -- 0 0 23 0

1 20 PID Feedback (PID FEEDBACK) R PID 0 Note 3 Note 3 Note 3

1 21 PID Setpoint Command (PID SETPOINT) R PID 0 Note 3 Note 3 Note 3

1 22 Actual Speed (ACTUAL FREQ) R Hz 2 0 12000 --

2 01 Fault Condition (OK.FAULT) R -- 0 OK FLT OK

3 01 Command Speed (COMMAND SPD) R/O Hz 2 0 120.00 20.00

3 02 Keypad Command Speed (CMD KEY SPD) R/O Hz 2 0 120.00 20.00

3 03 Normal Acceleration (ACCEL) R/O sec 1 * 3600.0 30.0

3 04 Normal Deceleration (DECEL) R/O sec 1 * 3600.0 30.0

3 05 Local PID Command R/O PID 0 Note 3 Note 3 Note 3

3 06 Control Mode R/O -- 0

4 01 History R/O -- 0 0 (maintain) 1 (clear) 0

4 02 Start/Stop Drive (CMD RUN.STOP) R/O -- 0 0 (stop) 1 (start) 0

4 03 Speed Control Auto/Manual R/O -- 0 0 (auto) 1 (manual) 0

4 04 Clear Present Fault (CLEAR FAULT) R/O -- 0 0 1 (clear)

NOTES:

1. Point Types: 1 = Analog Input; 2 = Binary Input; 3 = Analog Output; 4 = Binary Output

2. Current Value of the parameter version, software version and software revision.

3. Units, MIN/MAX Values: for this point are deﬁned via Drive Parameters #31, 75 and 76 respectively.

Refer to notes in sections 4.2 and 4.4.

* Refer to MC3000 Installation & Operation Manual (M301)

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Comentarios a estos manuales

Sin comentarios

Lenze MC3000 Series Drives Manual de usuario Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Lenze MC3000 Series Drives