Lenze i700 Manual de usuario descargar pdf (Pagina 3)

Lenze · i700 servo inverter · Reference manual · DMS 1.5 EN · 03/2014 · TD05 3

Contents

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

4.5 Monitoring of the DC-bus voltage _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 48

0x2540 - Device: Voltage values

4.6 Real-time information (distributed clock) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 50

0x2580 - ECAT DC: Real-time information

5 Motor control & motor settings _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 52

5.1 Required commissioning steps (short overview) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 54

5.1.1 Servo control for synchronous motor (SM) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 54

5.1.2 Servo control for asynchronous motor (ASM) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 55

5.1.3 V/f characteristic control for asynchronous motor (ASM) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 56

5.2 Commissioning functions (short overview) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 57

0x2822 | 0x3022 - Axis command

0x2823 | 0x3023 - Axis command: Progress

0x2825 | 0x3025 - Axis: Operating mode

0x2832 | 0x3032 - Identification: Status word

5.2.1 Enable/inhibit operation via control word _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 59

5.2.2 Saving changed parameters safe against mains failure _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 60

5.3 Wiring check by means of manual test modes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 61

0x2835 | 0x3035 - Manual test mode: Settings

5.3.1 Manual test mode "voltage/frequency" _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 62

5.3.2 Manual test mode "current/frequency" _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 63

5.4 Manual control _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 65

0x2836 | 0x3036 - Manual jog: Settings

5.5 Setting the control mode _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 69

0x2C00 | 0x3400 - Motor control

5.6 Accepting/adapting plant parameters _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 70

5.7 Compensating for inverter influence on output voltage _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 71

0x2DE0 | 0x35E0 - Advanced settings

0x2947 | 0x3147 - Inverter characteristic: Voltage grid points (y)

5.8 Setting the motor parameters for the servo control _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 75

5.8.1 Lenze motor: Easy loading of motor data from the catalogue via the »PLC-Designer« _ _ 75

5.8.2 Motors of other manufacturers or no catalogue data available: Three possibilities to create the

setting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 75

0x2C08 | 0x3408 - motor: Setting method - motor parameters

5.8.2.1 Enter motor nameplate data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 76

5.8.2.2 Set motor parameters manually _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 76

5.8.2.3 Determine motor parameters automatically via "motor parameter identification"

5.8.3 Motor parameters (object descriptions) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 81

0x2C01 | 0x3401 - Motor: Common parameters

0x2C02 | 0x3402 - Motor (ASM): Parameter

0x2C03 | 0x3403 - Motor (SM): Parameter

0x6075 | 0x6875 - Motor rated current

0x6076 | 0x6876 - Motor rated torque

5.9 Setting the feedback system for the servo control _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 85

5.9.1 General settings _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 86

0x2C45 | 0x3445 - open circuit in the feedback system: Response

0x2C46 | 0x3446 - feedback system: Specifiable number of revolutions

0x2C5F | 0x345F - Feedback system: Parameter CRC

5.9.2 Settings for "resolver" version _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 87

0x2C43 | 0x3443 - Resolver: Number of pole pairs

0x2C44 | 0x3444 - Resolver error compensation: Parameter

5.9.3 Settings for "encoder" version _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 89

0x2C40 | 0x3440 - Encoder: Type

0x2C42 | 0x3442 - Encoder: Parameter

1 2 3 4 5 6 7 8 ... 337 338

Comentarios a estos manuales

Sin comentarios

Lenze i700 Manual de usuario Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Software Lenze i700